REPAIRS‚ REHABILITATION AND RETRO-FITTING | Significance of Ferrocement repairs | After‚ we in India‚ started manufacture of concrete in years 1930’s‚ the negative aspect of concrete started showing after sometime as below:- | - Deterioration due to poor workmanship‚ particularly high water content and corrosion of reinforcement and R.C.C. Technology being new. | - Leakages in concrete due to rain water as well as in water retaining structures | This menace become conspicuous after construction
Premium Concrete Reinforced concrete
shearing force (SF) at any section of a beam represents the tendency for the portion of the beam on one side of the section to slide or shear laterally relative to the other portion. The diagram shows a beam carrying loads . It is simply supported at two points where the reactions are Assume that the beam is divided into two parts by a section XX The resultant of the loads and reaction acting on the left of AA is F vertically upwards and since the whole beam is in equilibrium‚ the resultant force
Premium Force Shear stress
Floor Systems The principal structural elements of a typical multi-storey building are the floors‚ beams‚ columns and foundations. The principal structural elements of a typical multi-storey building comprise floors‚ beams and columns. A wide variety of alternative forms and arrangements can be used in multi-storey steel framed structures. The principal structural elements of a typical multi-storey building Floor slabs: Several different types of slab can be used‚ in either composite or non
Premium Concrete Precast concrete
References: Aguinaga-Zapata‚ M. and Bazant‚ Z. (1986). “Creep Deflections in Slab Buildings and Forces in Shores during Construction” El-Shahhat‚ A. and Chen‚ W. (1992). “Improved Analysis of Shore-Slab Interaction”. ACI Structural Journal‚ 89(5)‚ 528-537. El-Shahhat‚ A.‚ Rosowsky‚ D. and Chen‚ W. (1993). “Construction
Premium Finite element method Concrete Ratio
Overview of Garment Manufacturing technology - Concentrating on cutting equipment [Document Subtitle] Abik Hirawat garment |ˈgärmənt| noun an item of clothing. ORIGIN Middle English : from Old French garnement ‘equipment‚’ from garnir ‘equip’ (see garnish ). Garment refers to any covering for the human body that is worn. Garment making is one of the basic content of fashion designing. . There are 2 types of garments. One is Woven garments. Another is Knitted garments Shirts‚ trousers
Premium Manufacturing Textile Clothing
along corresponding axes of rosette elements‚ in/in (m/m) ν = Poisson’s Ratio E = modulus of elasticity‚ psi (N/m ) y = deflection (in) P = force‚ lbs L = distance from clamp to loading micrometer (mm) x = the distance from the loading micrometer to the rosette centreline t = the beam thickness‚ in (m) b = beam width‚ in(m) c = semi thickness of the beam‚ in (m) M = bending moment at rosette centreline‚ psi(Pa or N/m²) ε p‚q = algebraically maximum and minimum principal
Premium Materials science Elasticity
experiment was conducted to find the impact of water on different types of vanes‚ it consists of 3 types the flat plate‚ conical cup and the hemispherical cup. Forces are generated by jet of water impacts the vanes that produces various angles of deflection. In the end the slope calculated was used to compare with the theoretical slope and the deviation slope was calculated. 1.0 Introduction One of the ways of producing mechanical work from fluid under pressure is to use the pressure to accelerate
Premium Mass Water jet cutter Force
Report content Introduction Two- dimensional stress and strain Multi- channel strain measurement Non- linear behavior of thin plates Objectives Theory and baackground Two- dimensional state of stress and strain Resistance strain gauges‚ gauge rosettes and strain measurement circuits Linearity of material behavior and structural behavior Equipment Arrangement of strain gauge rosettes on the plate Plate loading rig Procedures Loading Unloading Results Discussion
Premium Elasticity
2.0 Objectives : 1. To design a series type Ohmmeter using PMMC. 2. To understand the properties of series type Ohmmeter. 3. To design a series type ohmmeter when Ifsd=30μA is given. 4. To calculate the half scale deflection and full scale deflection of the series type ohmmeter from zero to infinity. 3.0 Equipment and component: No. | Equipment | Quantity | No. | Component | Quantity | 1. | DMM CD771(Series no:IN4/04/1260 ) | 1 | 5. | Crocodile clip | 4 | 2. | DC Ammeter(Series
Free Resistor Electrical resistance Electric current
Wendy Wiredu XRA 230 A. PERSONNEL PROTECTION * Primary X-Ray Beam * Emerges directly from the x-ray tube collimator. * It moves without deflection (toward a wall‚ door‚ viewing window‚ etc). * Primary radiation is also known as direct radiation. * Secondary Radiation (aka Scatter radiation & Leakage Radiaiton) * Scatter Radiation – results whenever a diagnostic x-ray beam passes through matter. * Compton interactions between the x-ray photons
Premium Ionizing radiation X-ray Radiology