Engineering Laboratory (Lab) Report Department of Engineering Faculty of Engineering and Science‚ University Tunku Abdul Rahman (UTAR) 1. Introduction Laboratory (Lab) reports are the most frequent document written by engineering student. These reports can contribute a significant amount of marks and yet little time or attention is devoted in understanding on how to write them well. The aim of this document is to provide a general guideline on writing a lab report. A lab report should not be
Premium Present tense Experiment Grammatical tense
CHEMISTRY LAB REPORTS How to Write a Lab Report Lab Reports gives the explanation of the experiment done Lab reports are an essential part of all laboratory courses and usually a significant part of your grade. If your instructor gives you an outline for how to write a lab report‚ use that. Here ’s a format for a lab report you can use if you aren ’t sure what to write or need an explanation of what to include in the different parts of the report. A lab report is how you explain what you did
Premium Theory Experiment Linguistics
growth of cells in two different yeast cultures; culture-A lacked the antibiotic and culture-B contained the antibiotic. Materials and Methods. -- To conduct this experiment there must be the following; a hemacytometer‚ a Pasteur pipette‚ and a compound microscope. A hemacytometer is a counting chamber to count the number of cells in a known volume. Pasteur pipettes
Premium Bacteria Standard deviation Arithmetic mean
Yeast Lab Report Guidelines 1. Lab reports are to be computer-generated and double-spaced. All sections of the report must be written in paragraph form. 2. Do not use encyclopedias (Internet or otherwise)‚ dictionaries ((Internet or otherwise)‚ or personal web pages as sources for the report‚ this includes Wikipedia. You may use a textbook‚ lab manual‚ and/or article(s) in a published journal. You can find journal articles by going to the library website: http://www.lib.clemson.edu/ and selecting
Premium Metabolism Yeast Citation
for it pH level. If the mixture is too acidic‚ then add sodium bicarbonate‚ as necessary‚ to reduce acidity. In the next step‚ add enough sodium chloride so that a small amount will remain after stirring. This will decrease the solubility of organic compounds and increase the amount of product that can be collected. Decant the liquid part of the mixture into a separatory funnel. Wait 5 minutes for the layers to separate and then drain the bottom layer into the Erlenmeyer flask and the top layer into
Premium Chemistry Water Solvent
is more accurate. Conclusion: During this lab I learn how to do simple and fractional distillation. Although the group I worked with only did simple distillation‚ I carefully observed how the group that did the fractional distillation. We collected all the results‚ to have a more precise range on what the results were. One way to produce an error in this process would have been if our procedures were done wrong or reversed or if we placed the compounds in a improper
Premium Chemistry Oxygen Water
finding its melting points‚ and by doing Thin-layer chromatography. When you reacted salicylic acid with FeCl3‚ changes in color will occur. Pure Aspirin has a melting point around 135°C and a pure salicylic acid has 158 °C. TLC is used to separate compounds based on affinity for stationary phase or mobile phase. In TLC‚ the solvent went up at different rates. The retention factor (Rf) of a component can then be measured by dividing the distance that was traveled by the solvent front distance.By doing
Premium Chemistry Acetic acid Water
A Report of Experiment 1 Purification and Identification of An Unknown Mixture Aim To separate a mixture of a neutral (ester‚ alcohol‚ ketone‚ aldehyde or ether) and an acidic compound (phenol or carboxylic acid) or a neutral and a basic compound (amine)‚ and to identify the unknown mixture by physical (M.P. or B.P.) and spectroscopic methods (NMR‚ IR and MS). Method The mixture (sample number: 27) was dissolved in 200 mL of CH2Cl2 and then extracted with 10% NaOH. The acid was removed
Premium Chemistry Molecule Chemical compound
produce ATP‚ by the ATP Synthase. The equation for this reaction is 6CO2 + 6H2O C6H12O6+6O2 or‚ carbon dioxide +water sugars + oxygen . This reaction takes place on the thylakoid membrane of the chloroplast and uses energy from sunlight to produce compounds like ATP and NADPH. The second stage of photosynthesis is the Calvin Cycle‚ which takes place in the stoma of the chloroplast. This stage is light-independent or it does not need energy from sunlight. During this reaction ATP and NADPH from Stage
Premium Carbon dioxide Photosynthesis Oxygen
Standards of tebuconazole (purity 96.6%)‚ trifloxystrobin (purity 99.6%)‚ CGA 321113 (purity 96.3%) and commercial grade fungicide formulation Nativo 75 WG (25 % trifloxystrobin and 50% tebuconazole) were supplied by M/s Bayer Crop Science Limited (Mumbai‚ India). The sorbent PSA (Primary secondary amine‚ 40µm particle size) was procured from Agilent Technologies (USA). HPLC grade acetonitrile‚ acetone and ethyl acetate were supplied by Merck (Mumbai‚ India). Analytical grade sodium chloride (NaCl)
Premium Mass spectrometry Green tea Tea