Page I - Cover sheet In the middle f the page give name and number of your microorganism In the right lower corner provide - your name - Lab section number (Biol 108-005) - Date submitted ( 4/18/2013) - the unknown tube # is 5 Page II table of result - This page will have your table of results include the following information - Name of the test - Medium used - Indicator used - your results Part III - All the test done As many pages as needed to do a complete job. in this section
Premium Organism Bacteria Biology
THE USE OF FISCAL INSTRUMENTS IN SUSTAINABLE BUILDING POLICIES M.M. Sunikka1 Abstract Although progressive government guidelines and knowledge about sustainable building exist‚ sustainability measures are not adopted in large scale. Several barriers have been identified‚ especially the perceived costs of implementing environmental management and the lack of market demand. The choice of fiscal instruments is an important issue in sustainable building policies. This paper presents an analysis
Premium European Union Sustainability
Evolution Lab Report Marcos Chapa July 3‚ 2013 BIO 101 Rebecca Avants The purpose of the lab I have conducted is to analyze how altering the finch’s environment would affect the evolution of the finches by isolating each population of finches from each other‚ placing them each on a different island. This influence on the species by the environment is called allopatric speciation. One population of the finches that are located Darwin Island‚ which is 1 km‚ and the other population of finches
Premium Evolution Species Hypothesis
Experiment AM1.2—Centrifugal Force Student name JunJie Liu Student ID 1512042 Experiment Date 11 Feb 2015 Lab group Mech 7 Introduction In this lab report we show the basic methods of measuring centrifugal force using two counter balanced bell-cranks spin on a turntable (shows in figure 1) and able to calculate the centrifugal force with given conditions shows in figure 1. *Figure
Premium Force Torque Experiment
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
I. Objective: The objective of this experiment is to determine the mass percent of iron in an iron compound using a spectrophotometer. From there‚ determine which iron compounds are in the stock room bottles based off of the experimental mass percent results. II. Introduction: The objective is to determine the mass percent of iron in an iron compound using a spectrophotometer. From there‚ determine which iron compounds are in the stock room bottles based off of the experimental mass percent results
Premium Chemistry Hydrogen Water
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
3M Optical Systems: Case Brief As Andy Wong‚ how would you handle the authorization for expenditure for the re-launch of the privacy screen? As Andy Wong‚ I would take the proposal to one of my senior-level mentors for support. The OS unit has already tried and failed three times with the microlouvered filter and high level support would benefit both Wong and Guehler in this case. If Guehler sees that other areas of 3M are in support of the authorization for expenditure‚ then he will not have
Premium Management Marketing Strategic management