concentrations of solutes in and out of the cell. Filtration is what is used to remove solid particles and they can be removed by passing through a liquid and gas. The information above is very important because it is exactly what everything in this lab will be about. It explains in detail what every single little definition and important
Premium Osmosis Diffusion Membrane biology
Daphnia Experiment Report 1. Introduction Caffeine is found in many plant species‚ where it acts as a natural pesticide. It is found most commonly in cocoa‚ tea and coffee‚ but is also artificially added to some soft drinks such as cola to act as a flavour enhancer. When consumed by humans‚ caffeine works as a stimulant causing amounts of released neurotransmitters to be increased. High use of caffeine has been related with raised blood pressure‚ restlessness‚ insomnia and anxiety which‚ in
Premium Heart rate Caffeine Experiment
This lab has introduced the use of daphnia‚ pill bugs‚ amoeba and Uglena. We the AP Biology students were first introduced to the test subjects to test his or her capability of handling living organisms for upcoming science experiments. The AP Biology students were asked to create original experiments for all test subjects testing reactions to gravity‚ light intensity and reaction to food. Daphnia‚ or Daphnia magna‚ are microscopic organisms in which the students created an original lab to test
Premium Cell Microorganism Bacteria
LAB # 5 Relationship Between Drop Height and Diameter of Plasticine Sphere PROBLEM: A student suggest that there is a proportional relationship between height at which a plasticine sphere is dropped and the diameter of the flattened part after dropping. Design an experiment to determine if this suggestion is true or not. AIM: To investigate the relationship between the drop height and the flattened part of a plasticine sphere after being dropped. HYPOTHESIS: As the height of the sphere plasticine
Premium Measurement Circle
Use a study guide only please and note two of the answers are wrong regarding conversions.!! Up to you to figure which ones. Just know its nice to compare answers to see if your on the right track. LAB 1 1. Describe the function of the following pieces of safety equipment and how each might be used: (10 points) a. Eye Wash (2 points) a. The function of the eye wash station is to flush your eyes of any chemicals or other harmful liquids you may have gotten in your eyes. You would
Premium Temperature Scientific method Celsius
Solute Concentration of Potatoes Lab #1 Purpose: To find the molarity/concentration of potato cytoplasm. Materials: As on page 1 in the lab handout. Procedure: As on page 1 in the lab handout. Data and Observations: Test Tube # | Concentration of sucrose solution (mol/L) | Initial Mass (g) | Final Mass | Percentage change in mass | 1 | 1.0 mol/L | 3.00g | 2.25g | -25.0% | 2 | 0.9 mol/L | 2.70g | 2.07g | -23.3% | 3 | 0.8 mol/L | 2.92g | 2.25g | -22.9% | 4 | 0.7 mol/L | 2.60g
Premium Concentration Osmosis Chemistry
Physics 211 Experiment #4 Newton’s Second Law – Atwood’s Machine Newton’s second law (FNET = ma) can be experimentally tested with an apparatus known as an “Atwood’s Machine” (See Figure 1.) Two weights of unequal mass‚ connected by a thread‚ are draped over a pulley‚ as shown in the figure. When released‚ the larger mass accelerates downward and the smaller one accelerates upward. Figure (1a): The Atwood’s Machine‚ showing the pulley and the two masses after a run. Figure (1b): A close
Premium Mass Microsoft Excel Acceleration
Lab Report Experiment 1 & 2 CHM-101 Amele Takpara Partner: Jessamyn Dupree ------------------------------------------------- Experiment 1 ------------------------------------------------- (Pre-Lab Questions) 1. In the design of a Bunsen burner‚ explain the purpose of a. the gas control valve The gas control valve regulates the rate at which methane enters the burner. b. and the air vents. The air vents control the rate at which air enters the burner 2. Why is a luminous
Premium Temperature Volume Liquid
Hooke’s Law Lab Report Please complete the following tables and questions and submit them on Blackboard. Observations Data Table 1. Force (N) Top position of spring‚ cm Bottom position of spring‚ cm Elongation‚ cm Bottom reading – top reading Data Point 1 .8 4 5 1 6Data Point 2 1.3 4 6 2 Data Point 3 1.5 4 7 3 Data Point 4 2 4 8 4 Data Point 5 2.2 4 9 5 Data Point 6 2.5 4 10 6 Data Point 7 2.7 4 11 7 Data Point 8 3 4 12 8 Data Point 9 3.3 4 13 9 Data Point 10 3.6 4 14 10 Data Table 2.
Premium Elasticity Robert Hooke Force
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control