Experiment AM1.2—Centrifugal Force Student name JunJie Liu Student ID 1512042 Experiment Date 11 Feb 2015 Lab group Mech 7 Introduction In this lab report we show the basic methods of measuring centrifugal force using two counter balanced bell-cranks spin on a turntable (shows in figure 1) and able to calculate the centrifugal force with given conditions shows in figure 1. *Figure
Premium Force Torque Experiment
Results Experiment I: As a general trend O2 production and reaction velocity increased with increasing catalase concentration‚ however‚ the 33% percent catalase concentration showed a drop of 0.175 mL O2/s compared to the 25% catalase concentration (figure 1.2). The velocity of 25% catalase was 0.275 mL/s‚ 33% was 0.1 mL/s‚ 50% was 0.435 mL/s‚ and 75% catalase was 0.575 mL/s (figure 1.1). The 50% catalase concentration produced the most O2 overall however the 75% catalase concentration had the fastest
Premium Enzyme Chemical reaction Chemical kinetics
Physics Lab report Aammar Paracha Section MX Feb 6th 2015 OPTICS Abstract: This experiment revolves around using light rays and lenses. The experiment also discusses different properties of light rays. This experiment uses different lenses and measurements to produce images and observes different techniques to obtain the image position. Question and Answers: 1. Use your data to verify the Law of Reflection and then use Snell’s Law to calculate
Premium Optics Lens
Biology vol. 1 Chp 7 pp 125-141. San Francisco‚ California Marieb E.‚ Mitchell S.‚ (2009) Cell Transport Mechanisms and Permeability: Computer Simulation. Pearson Education. Human Anatomy & Physiology Lab Manual. Chp. 5th pp 53-63. San Francisco‚ California Marieb E.‚ Mitchell S.(1995)Human Anatomy and Physiology Physio-Ex Retrieved july 4 2010. From web site: http://wps.aw.com/bc_marieb_aplabs_9/58/15037/3849530. cw/index.html
Premium Diffusion Osmosis Semipermeable membrane
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume