Preview

A+ Certification

Satisfactory Essays
Open Document
Open Document
285 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
A+ Certification
Basis :

1. When taking a computer apart, why is it important to not stack boards on top of each other? You could accidentally dislodge a chip this way.

2. Why is it important to remove loose jewelry before working inside a computer case? That might caught In cables and components as you work

3. When assembling a System which do you install first, the drives or the motherboard? The mother board

4. What is the purpose of raised screw holes or standoffs installed between the motherboard and case? Holds the Motherboard in place

5. When installing the front panel wires to the motherboard front panel header, how do you Look for a small triangle embedded on the connector that marks one of the outside wires as pin 1 know which pins to use for each wire if the pins on the header are not labeled? Turn to the motherboard user guide for help

6. What are the two major components of a processor cooler assembly? Fan and a heat sink.

7. How many pins does the CPU fan header on a current motherboard have? 4-PIN

8. If the power connector from the CPU fan has only three pins, it can still connect to the pin header, but what functionality is lost? No one, will always operate at the same speed

9. How do you determine the wattage capacity needed by a power supply? When deciding what wattage capacity you need for the power supply, consider the total wattage requirements of all components inside the case as well as USB and FireWire devices
The power supply should be rated about 30 percent higher than expected needs 10. Which one component in a high-end gaming computer is likely to draw the most power? Video cards draw the most power.

You May Also Find These Documents Helpful

  • Satisfactory Essays

    NT1310 Unit 6 Exercise 1

    • 419 Words
    • 2 Pages

    On a TWISTED PAIR CABLE I chose to install an RJ-45. This is the standard Ethernet connector for most systems used today. I would first measure out the length of cable that I would need. I would then use a wire cutter to cut the length that I need, leaving enough room for corrections and to open the wire. I would then use wire strippers to remove a small piece of the outer most jacket. I would then choose what connection I wanted to make (568A or 568B). I would then untwist the wires and put them in the correct color order that I need. Then I would flatten out the wires and in one hand hold my RJ-45 connector and then with the other hand feed the wires into the connector. This is usually pretty simple with the way the connectors are made, and they are also usually clear. After I’m sure that the wires are in the connector all the way, and in the right order, I would use a wire crimper to clamp the wires securely into the connector.…

    • 419 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    Typically on the motherboard and the only part the user sees is the expansion plate containing multiple…

    • 603 Words
    • 3 Pages
    Satisfactory Essays
  • Satisfactory Essays

    NLX low end PC fit into expansion slots riser cards are also called daughter boards. Provide connector for additional expansion cards…

    • 399 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    Nt1310 Unit 2 Formulas

    • 498 Words
    • 2 Pages

    71,825/703 < 703w/703 < 92,950/703 Now, I will take all three components and divide by…

    • 498 Words
    • 2 Pages
    Good Essays
  • Satisfactory Essays

    Nt1310 Unit 5 Essay

    • 437 Words
    • 2 Pages

    Case - A case is a sort of chassis for the internals of a computer and acts as a kind of protection from dust etc. It is also more appealing to look at rather than the internals of the computer.…

    • 437 Words
    • 2 Pages
    Satisfactory Essays
  • Powerful Essays

    Pt1420 Unit 1 Assignment 2

    • 1305 Words
    • 6 Pages

    Das, D., Gregersen, E., Hosch, L., Lotha, G., Sampaolo, M., Sinha, S. (2014). C++. In Encyclopedia Britannica.…

    • 1305 Words
    • 6 Pages
    Powerful Essays
  • Good Essays

    4. Where on the disk should you put your /boot partition or the root (/)…

    • 638 Words
    • 2 Pages
    Good Essays
  • Good Essays

    Nt1310 Unit 4

    • 707 Words
    • 3 Pages

    Use the CHS Reference Chart to record the current components found on the CHS computer:…

    • 707 Words
    • 3 Pages
    Good Essays
  • Satisfactory Essays

    There are several different buses on a motherboard. Each one has a unique function. Each of the buses are used to control and alter many applications and functionality of the computer. These buses control so much information in the computer that not a single bus can take the place of two or more. There is simply too much information that would cause the bus to overload and could short out.…

    • 218 Words
    • 1 Page
    Satisfactory Essays
  • Powerful Essays

    This is a circuit board that connects the CPU with the RAM and the hard drive…

    • 1180 Words
    • 5 Pages
    Powerful Essays
  • Satisfactory Essays

    X86 and Internet Explorer

    • 269 Words
    • 2 Pages

    2. Using Internet Explorer, locate information on the LGA 1156 connector. What processors is it used with? What is its purpose on the motherboard?…

    • 269 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    NT1110 Module3 SA

    • 365 Words
    • 1 Page

    The motherboard is the foundation of the computer. Everything that makes up a computer has to be attached to the motherboard. The motherboard has many components such as a processor, memory, chipset, expansion slots, and inputs/outputs.…

    • 365 Words
    • 1 Page
    Satisfactory Essays
  • Satisfactory Essays

    5. When installing the front panel wires to the motherboard front panel header, how do you know which pins to use for each wire if the pins on the header are no0t labeled?…

    • 452 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    i need help

    • 300 Words
    • 2 Pages

    5. Draw a diagram of how the wires are connected, they are never labeled well on a motherboard. Make a careful diagram and then disconnect the wires.…

    • 300 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    admin

    • 1134 Words
    • 3 Pages

    1.4 – First you secure the PSU inside the case securely by screwing it from the back of the case. Next, you put the special motherboard posts in the back of the case matching the holes of the…

    • 1134 Words
    • 3 Pages
    Good Essays