Experiment AM1.2—Centrifugal Force Student name JunJie Liu Student ID 1512042 Experiment Date 11 Feb 2015 Lab group Mech 7 Introduction In this lab report we show the basic methods of measuring centrifugal force using two counter balanced bell-cranks spin on a turntable (shows in figure 1) and able to calculate the centrifugal force with given conditions shows in figure 1. *Figure
Premium Force Torque Experiment
------------------------------------------------- Name: ------------------------------------------------- Biology 104 ------------------------------------------------- Lab Section: 14 ------------------------------------------------- TA: Victoria Prescott ------------------------------------------------- Date: 9/13/2012 ------------------------------------------------- ------------------------------------------------- The Effects of Light Intensity and NaHCO3 concentrations on the Rate
Premium Philadelphia Computer software Mobile computing
Physics Lab report Aammar Paracha Section MX Feb 6th 2015 OPTICS Abstract: This experiment revolves around using light rays and lenses. The experiment also discusses different properties of light rays. This experiment uses different lenses and measurements to produce images and observes different techniques to obtain the image position. Question and Answers: 1. Use your data to verify the Law of Reflection and then use Snell’s Law to calculate
Premium Optics Lens
Title: The Effect of Varying Amounts of Substrate and Enzyme on a Reaction Rate Abstract In living organisms‚ certain reactions must take place rapidly to assist life. This occurs because of enzymes‚ because all reactions would take place too slowly to sustain life (Jacklet‚ 237). Enzymes are large protein molecules that catalyze specific chemical reactions without being used up in the process. Each enzyme has a region on its surface‚ called the active site‚ which recognizes a specific
Premium Enzyme Chemical reaction Catalysis
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
INTRODUCTION This scientific report is to discuss the results of an experiment being conducted on the effect that antibiotics have on the growth of bacteria. This will be done through the use of microbiology. Microbiology is a science in the department of biology‚ particularly microorganisms. These include; bacterium‚ fungi‚ protozoa‚ algae and viruses. This is an important subject to study as microorganisms can be found everywhere‚ covering all matters of different surfaces even including the human
Premium Bacteria Microbiology Microorganism
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume