Experiment 2: IDENTIFICATION OF UNKNOWNS BY TLC AND MP IN COMBINATION Introduction: Thin layer chromatography (TLC) is one of the most valuable techniques in organic chemistry. This is a best method of separating and identifying mixtures of two or more compounds. The separation is accomplished by the distribution of the mixture between two phases: one that is stationary and one that is moving or mobile. Chromatography works on the principle that different compounds will have different
Free Chromatography Thin layer chromatography
the pipe with the outside diameter (O.D.) of 25 millimeters was continuously produced for each anti-rodent-added PE compound. Two groups of experiments were planned for this investigation; laboratory experiments including impact resistance‚ tensile elongation‚ environmental stress cracking (ESCR)‚ melt flow rate (MFR)‚ and differential scanning calorimetry (DSC) were carried out on the control (anti-rodent free) and anti-rodent-added PE100 test samples prepared in the laboratory. Also‚ a group
Premium Tensile strength Pipeline transport Experiment
Experiments in physics lab report Department of Electrical Engineering Isabela State University Ilagan Campus‚ Calamagui 2nd‚ City of Ilagan‚ Isabela baccaljoemel@yahoo.com Submitted to: Engr. Rafael S. Ramos Physics12 Professor Submitted by: Joemel L. Baccal BSEE IIA Experiments in Physics Lab Report Joemel L. Baccal Department of Electrical Engineering Isabela State University - Ilagan Campus‚ Calamagui 2nd‚ City of Ilagan‚ Isabela baccaljoemel@yahoo.com Abstract In
Premium Electric charge Electromagnetism
In this experiment‚ we used acquired observational data to develop an activity series describing the relative reactivity of the metals being tested. The elements within a periodic table often show different trends in physical and chemical properties depending on the period or group they are apart of. In a periodic table‚ elements are arranged by increasing atomic number in horizontal rows called periods. The atomic numbers represent the number of protons in each element. The periodic table is also
Premium Chemistry Chemical element Periodic table
FIRE RESISTANT BALLOON: Materials - 1 matchbox - 1 candle - 1 yellow colored balloon - 1 blue colored balloon - Half a cup of water Procedure: 1. For this experiment‚ the independent variable is whether the balloon is filled with water or not. The dependent variable is what happens to the balloon when it is placed above the lit candle. This is determined by observing the balloon. The constants (control variables) are how much the balloon is inflated and the amount
Premium Water Ocean Salt
Aim: The aim of this experiment is to convert copper metal through a series of intermediate copper compounds back into copper metal. By weighing the copper at the beginning and at the end of the experiment the percentage yield can be determined. Method: The experiment was carried out as outlined in the practical manual. Results: Table: showing masses: Mass copper wire 0.2510 Mass crucible 28.9257 Mass watch glass 19.6213 Mass watch glass + copper 19.7890 Mass copper
Premium Chemistry Copper Chemical reaction
process of distillation. Distillation is the separation of volatile substances mixed with nonvolatile substances by boiling the mixture to alter the phase of the volatile substance. The researchers used the simple distillation set up to conduct the experiment. 25 ml of The Bar Vodka was used and 7 ml of distillate was collected before a temperature of 95 degrees Celsius was reached. Collected distillate was then subjected to a flammability test to confirm ethanol content. The percent ethanol was computed
Premium Distillation Boiling point Ethanol
To begin the experiment‚ the unknown needs to be determined as an acid or a base by using litmus paper or a pH strip. For the rest of the experiment‚ if the substance is being handled‚ gloves and goggles must be worn. Use a clean and dry Erlenmeyer flask and weigh it. Then‚ some of the unknown will be measured and poured into the flask. Also way the flask and the unknown. Add distilled water and phenol saline to the flask. Set that aside to prepare the biuret. Choose the substance that will be used
Premium Chemistry Chemical substance Oxygen
this makes it easier and safer to extinguish the flames. 2 Make sure the wick fits tightly in the wick holder and that the wick holder fits tightly in the burner. 3 Fill and label spirit burners or dropper bottles with alcohols in advance of the experiment. Ensure any excess alcohol is wiped off the side of the burners. 5 careful considerations must be given on igniting the alcohols. The spirit burners must be kept upright when lighting. Do not tip onto the side. 6 make sure the alcohols are
Premium Ethanol Thermodynamics Heat
06.03 Calorimetry: Lab Report Before You Begin: You may either copy and paste this document into a word processing program of your choice or print this page. Part I The Dissolving of Solid Sodium Hydroxide in Water Procedure: 1. Measure out approximately 200 mL of distilled water and pour it into the calorimeter. Stir carefully with a thermometer until a constant temperature is reached. Record the volume of water and the constant initial temperature of the water on your data table.
Premium