orientation of a piezoelectric material during the design and manufacture of a device. There are certain mechanical parameters which plays a great role in piezoelectric effect. 2.2.1 Mechanical Strain The mechanical strain S which results from the application of a stress T is linearly proportional to the compliance S (S-1= Young’s modulus) within the elastic deformation region of the stress-strain curve of the material (below the yield strength )
Premium Force Elasticity Mass
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
Protocol for Lab 5 – Aerobic Respiration Part 1 Isolation of Mitochondria from Cauliflower - Weigh 50g of rosettes cut from fresh cauliflower head. - Cut rosettes and place it on ice - Prepare juice extractor by placing ice and an empty 150 ml beaker into the right compartment. - Collect pulp from left compartment and record total volume of the extract. Approx. 20ml - Filter the pulp using six layered cheese cloth and collect it in a beaker sitting on ice. - Place two 50 ml test tubes
Premium Cellular respiration Adenosine triphosphate Citric acid cycle
Floyd Askew 3/19/13 CHEM 1211L Lab Report Introduction The purpose of this lab is to use volumetric analysis to determine the concentration of unknown substances. A sodium hydroxide solution is standardized to assist in finding the concentration of an acetic acid. An indicator must be used to pin point the equivalence point‚ the point in which 1 mole of a substance is equal to 1 mole of another. When that is found‚ we can determine the concentration. HC2H3O2 (aq) + NaOH (aq)
Premium Titration Sodium hydroxide PH indicator
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Temp= 21.5°C)‚ and SAMPLEs 3‚ 4‚ and 5 data was taken on 21.15.14 (Room Temp= 22°C). QUALITATIVE DATA: same water used for last first 2 samples‚ and same water used for last 3 samples pringles become black color with white dusting pool of oil/unknown substance fills bottom of petri dish [filmy brown] glass beaker enveloped with soot/smoke residue chips released thick blackish-grey smoke pringles are fluffy and soft [after burning]‚ collapse at touch sizzling oil sound pringle becomes [in
Premium Energy Heat Mass
generally followed immediately by cytokinesis‚ which divides the nuclei‚ cytoplasm‚ organelles and cell membrane into two daughter cells containing roughly equal shares of these cellular components. Mitosis and cytokinesis together define the mitotic (M) phase of the cell cycle‚ the division of the mother cell into two daughter cells‚ each with the genetic equivalent of the parent cell. In simple terms‚ mitosis is the process where non sex cells reproduce by duplicating DNA and dividing into two identical
Premium Chromosome Meiosis Eukaryote
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume
This lab experiment investigates the effect of listening to different types of music on one’s pulse. The experiment relates the circulatory system to the pulse as it measures how quickly the heart contracts and releases blood. Pulse is measured in beats per minute (bpm). One’s pulse is loudest near the heart‚ because there is more pressure closer to the heart. In contrast‚ one’s pulse is quieter the further away it is measured from the heart‚ because there is less pressure the further the distance
Premium Heart Psychology Experiment