NaHCO3 x 1mol Na2CO3 over 2 mol NaHCO3 x 105.987g Na2CO3 x 1 mol Na2CO3. Hence‚ I multiplied 3.2 x 1 x 1 x 105.987 and got 339.1584. Afterwards‚ I divided 339.1584 by 84.007 and got 4.04. Then‚ I divided 4.04 by 2 and got 2.02. In order to get my percent yield I divided 2.02 by 3.2 plus multiplied that by 100 getting 62.8. Now‚ when I had started of the experiment‚ I had
Premium Chemistry Carbon dioxide Sodium hydroxide
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
1.0 Abstract The elastic modulus‚ yield point‚ and ultimate strength of mild steel were determined in uniaxial tension. The "dogbone" specimen geometry was used with the region of minimum cross section having the dimensions: thickness =1.04 mm‚ width = 3.14 mm‚ and length section = 30 mm. This experiment was accomplished by first placing our specimens one at a time into a tensile testing machine (A G.U.N.T Hamburg Tensile Testing Machine (Max. load = 2kN))‚ which‚ under physical control‚ slowly
Premium Tensile strength Elasticity Materials science
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Lab Report #1 Title: Synthesis of Divanillin Abstract: The purpose of this experiment was to synthesize divanillin. This was done via the oxidative dimerization of two equivalents of vanillin‚ using enzyme horseradish peroxidase as the catalyst. Procedure: Lab Handout: Nishimura‚ R.T.; Giammanco‚ C.H.; Vosburg‚ D.A. J. Chem Educ. 2010‚ 87‚ 526-527. Discussion: Mechanism: Reaction 2 Vanillin H2O2 Divanillin 2 H2O
Premium Molecule Oxygen Atom
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Introduction The purpose of this lab was to calculate and determine the optimal dosage of ultraviolet (UV) light to expose Saccharomyces cerevisiae (S. cerevisiae) to that would result in a survival rate of 20-40%. Saccharomyces cerevisiae commonly referred to as baker’s yeast is a single-celled eukaryote. Yeast is capable of growing as either a haploid or a diploid cell. The diploid cell can reproduce mitotically or sporulate‚ a process initiating meiosis and forming an ascus with four spores (Sacchromyces
Premium Yeast Bacteria Metabolism
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume
ABSTRACT On the past two weeks‚ I have done an experiment on hydrostatics‚ or is also known as fluid statics (fluid at rest) within the fluid mechanics field of study. This condition explains that in a stable condition‚ the fluid is at rest. The use of fluid in doing work is known as hydraulics‚ and the science of fluid in motion is known as fluid dynamics. INTRODUCTION The natural nature of fluids are they cannot remain stationary under the application of shear stress. However‚ fluid
Premium Fluid mechanics Force Fluid dynamics