Using 10 Pine Boards Lab Report
Using ten pine boards 1.905 cm. by 2.54 cm. leaving 0.3175 cm. gaps between the boards forming a rectangular base held together with 1.27 cm. brad nails installed with a nail gun.
Adding 4 boards on the outer perimeter with the nail gun. Forming the edge sides.
Using a skill saw cut a 38.1 cm by 25.4 cm. rectangle out of your 0.635 cm. luan board (plywood). Repeat another time so that you have two of these boards.
Using a skill saw cut a gable end at a 6-12 pits.
Using a square to square the building walls up glue the walls together by spreading the wood glue into the grain. Placing them together and holding the pieces together using the duct tape.
Wait for 24 hours for the wood glue to dry. Then remove the duct tape.
Then cut 8 wood slats …show more content…
long by 2.54 cm. wide and the 22.86 cm. by 2.54 cm. boards, but with nothing inside. Now take the fiberglass and cut 2 new pieces without trying to compress it and cut them 27.94 cm. by 22.86 cm. thick.
Wait for the glue to dry overnight.
Now the fiberglass panels go in the empty rectangles corresponding to their size. Tape the pieces in the rectangle on the paper side to the boards.
After that cut two pieces of wood 22.86 cm. by 40.64 cm. Then cut two triangles with a base of 22.86 cm. and sides of 15.24 cm.
Cut two more pieces of wood 38.1 cm. by 2.54 cm. by 1.905 cm.
Grab the two pieces of wood 22.86 cm. by 40.64 cm. and tape the pieces of wood together on the top and the bottom. Then place the triangle on one of the sides of the board with the board horizontal, place an in. from the side. Mirror on the opposite side.
Place the 38.1 cm. by 2.54 cm. by 1.905 cm. wood 10.16 cm. from the horizontal edge and glue in place. Then screw in place on the other side of the long board.
Screw the two screws in the triangle and the wood slats. Do this on the other three sides too.
Wait for glue to dry overnight.
Run a cable through the bottom of the floor.
Connect the light socket to this cable in the box and screw it to the floor of the
Adding 4 boards on the outer perimeter with the nail gun. Forming the edge sides.
Using a skill saw cut a 38.1 cm by 25.4 cm. rectangle out of your 0.635 cm. luan board (plywood). Repeat another time so that you have two of these boards.
Using a skill saw cut a gable end at a 6-12 pits.
Using a square to square the building walls up glue the walls together by spreading the wood glue into the grain. Placing them together and holding the pieces together using the duct tape.
Wait for 24 hours for the wood glue to dry. Then remove the duct tape.
Then cut 8 wood slats …show more content…
long by 2.54 cm. wide and the 22.86 cm. by 2.54 cm. boards, but with nothing inside. Now take the fiberglass and cut 2 new pieces without trying to compress it and cut them 27.94 cm. by 22.86 cm. thick.
Wait for the glue to dry overnight.
Now the fiberglass panels go in the empty rectangles corresponding to their size. Tape the pieces in the rectangle on the paper side to the boards.
After that cut two pieces of wood 22.86 cm. by 40.64 cm. Then cut two triangles with a base of 22.86 cm. and sides of 15.24 cm.
Cut two more pieces of wood 38.1 cm. by 2.54 cm. by 1.905 cm.
Grab the two pieces of wood 22.86 cm. by 40.64 cm. and tape the pieces of wood together on the top and the bottom. Then place the triangle on one of the sides of the board with the board horizontal, place an in. from the side. Mirror on the opposite side.
Place the 38.1 cm. by 2.54 cm. by 1.905 cm. wood 10.16 cm. from the horizontal edge and glue in place. Then screw in place on the other side of the long board.
Screw the two screws in the triangle and the wood slats. Do this on the other three sides too.
Wait for glue to dry overnight.
Run a cable through the bottom of the floor.
Connect the light socket to this cable in the box and screw it to the floor of the