SAFETY General WHMIS beforehand – no messing around on anything‚ no food/drink anywhere PPE – goggles‚ coat‚ feet Treatment Skin Chem: emergency shower – TA/HS Eye Chem: eye wash – 10 mins. TA/HS Fire Emergency kill switch for gas‚ electricity and water – leave and set the alarm Stop drop and roll Apparati should be clear of any controls or switches‚ keep vapours to minimum/take need Extinguishers – on the wall inside each 1st year lab Class A - ordinary combustibles
Premium Acid
INTRODUCTION 1. INTRODUCTION The copolymerization of ethylene with 1‚ 3-butadiene to give crystalline‚ homopolymer-free‚ high molecular weight‚ substantially linear copolymer is described. Butadiene polymerizes almost exclusively in a trans-1‚ 4 structure‚ ranging in content from zero to 50 mole-%. At relatively low content of butadiene monomeric units (≤30 mole-%) X-ray crystallinity is of polyethylene type with a slight variation of the structural parameters. At higher levels of
Premium Polymer
Chapter 1: Intermolecular Forces: Liquids‚ Solids‚ and Phase Changes Chem 11: General Chemistry 2 Topics 1.1 An Overview of Physical States and Phase Changes 1.2 Quantitative Aspects of Phase Changes 1.3 Types of Intermolecular Forces 1.4 Properties of the Liquid State 1.5 Uniqueness of Water 1.6 The Solid State: Structure‚ Properties and Bonding A hot spring on a snowy day The Kinetic Molecular View of the Three States The characteristic properties of gases‚ liquids
Premium Water Atom Fundamental physics concepts
SMK RAPAT SETIA PROJEK MATEMATIK TAMBAHAN 3472/2 Nama Calon : Angka Giliran : No. IC : Nama Guru : ISI KANDUNGAN No. Butiran 1.0 Perakuan calon 2.0 Penghargaan 3.0 Objektif 4.0 5.0 Perakuan Calon Tentang Ketulenan Tugasan Projek Kertas 3472/2 Saya memperakui bahawa Tugasan Projek yang dikemukakan untuk memenuhi syarat Peperiksaan Sijil Pelajaran Malaysia 2013 bagi mata pelajaran Matematik
Premium Vitamin
THIS DOCUMENT IS PROTECTED BY U.S. AND INTERNATIONAL COPYRIGHT It may not be reproduced‚ stored in a retrieval system‚ distributed or transmitted‚ in whole or in part‚ in any form or by any means. Downloaded from SAE International by Loughborough University‚ Friday‚ June 29‚ 2012 01:25:49 PM Direct Injection Diesel Engine Rate of Heat Release Prediction using Universal Load Correction Factor in Double Wiebe Function for Performance Simulation 2011-01-2456 Published 04/01/2012 S. Loganathan‚ R
Premium Diesel engine Internal combustion engine
Macronutrients Vs Micronutrients Macronutrients Big components Protein Carbohydrate Fat Fibre Micronutrient Need less off Vitamin Trace elements Energy Food and nutrients supply our bodies with energy Energy = Kilojoules + Calories 4.18 Kj to a Calories Nutrient poor – lots of KJ but not a lot in the nutrients Basic Anatomy Salvia Starts mouth finishes in intestines Involves enzymes specific to each nutrient 2-72 hours to complete Bile – breakdown and emulsifies fats Proteins – protesters Villi Cells Fats
Premium Nutrition
Pemphigus as a paradigm of autoimmunity and cell adhesion. Keio J Med 51: 133–139. * Green KJ‚ Jones JC. 1996. Desmosomes and hemidesmosomes: Structure and function of molecular components. FASEB J 10: 871–881. * Amagai M‚ Matsuyoshi N‚ Wang ZH‚ Andl C‚ Stanley JR. 2000. Toxin in bullous impetigo and staphylococcal scalded-skin syndrome targets desmoglein 1. Nat Med 6: 1275–1277. * Bass-Zubek AE‚ Green KJ. 2007. Biochemical characterization of the desmosome. J Invest Dermatol 127: E4–E5. * Berkowitz
Premium Protein Cell membrane
THE COLLEGES OF OXFORD UNIVERSITY PHYSICS Wednesday 5 November 2008 Time allowed: 2 hours For candidates applying for Physics‚ and Physics and Philosophy There are two parts (A and B) to this test‚ carrying equal weight. Attempt as many questions as you can from each part. Write on white A4 lined paper. At the end of the test put your answer sheets in order and collate with a treasury tag. Attach a cover sheet to your answers. DO NOT write your name anywhere except on the cover sheet.
Premium Mass Orders of magnitude Energy
Materials and Manufacturing 2 Processing and testing of polypropylene Part A. Injection molding of polypropylene samples for mechanical testing. Introduction Injection molding is the most productive and popular polymer processing techniques. Almost 70% of all plastic parts are made using injection molding. Injection molding of plastics is a process similar to die casting of metals. Molten polymer is injected under pressure into a mold. Method Put the plastic material (Polypropylene)
Premium Materials science Tensile strength Plastic
the summer. The nutritional value of this drink is not very high. With a total of 180KJ per 100ml‚ coke is exceedingly high in kilojoules. To simply show comparisons‚ the recommended daily KJ intake for an average teenager is approximately 8200 (K. Baker‚ 2010). Despite the fact that this drink is fairly high in KJ‚ not surprisingly‚ it does not provide a long energy period for a drinker of any age. To put into context‚ an average 340ml can of coca cola contains 145 calories and over 45g of sugar. Per
Premium Coca-Cola