’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
Abstract Photosynthesis is a food making process for algae and plants. The photosynthesis process rate varies from different wavelengths and intensities of light. This lab will evaluate the optimal wavelengths and degrees of intensity during photosynthesis when chloroplast is exposed to light. The mixtures of DCPIP with water‚ PO4 buffer‚ and chloroplast will be prepared in a number of cuvettes. The cuvettes were tested individually at different wavelengths and intensities to find the optimal rate
Premium Photosynthesis
Introduction and Purpose: This lab focuses on how weight affects the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s) respectively. The primary goal of this lab is to investigate and explain the relationship of these two factors. During the process of conducting this experiment‚ learning to design a lab will also be achieved. Research Question: What is the effect of weight on the time it takes for a rotocopter to fall from a drop height of 1 and 2 meter(s)? Variable
Premium Force Classical mechanics Mass
Sugar Gradient Lab Procedure: 1. Get out 5 separate cups or beakers and fill them ¾ full with water in each. 2. Number each of the cups 1 through 5. And color accordingly with food dye: • Cup 1- 2 drops of yellow • Cup 2- 2 drops of red • Cup 3- 2 drops of green • Cup 4- 2 drops of yellow and 1 drop of red • Cup 5- 2 drops of blue 3. Add: • 1 scoop of sugar in Cup 1 • 2 scoops of sugar in Cup 2 • 3 scoops of sugar in Cup 3 • 4 scoops of sugar in Cup 4 • 8 scoops of sugar in Cup 5 4
Premium Mix Chemistry Mixture
Impurity Lab Report Aim: To find out the difference of the boiling point and melting point when adding impurity (salt) to water. Diagram: Method: 1.Set up the apparatus as shown in the diagram 2. Get a known amount of ice in the beaker (half full)‚ and a known amount of salt in another beaker 3. Measure the temperature (melting point) of the ice without adding any impurity (salt). 4. Measure the temperature (melting point) of the ice after adding the salt into the beaker. 5. Heat up
Premium Water Solid Fahrenheit
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume
ABSTRACT On the past two weeks‚ I have done an experiment on hydrostatics‚ or is also known as fluid statics (fluid at rest) within the fluid mechanics field of study. This condition explains that in a stable condition‚ the fluid is at rest. The use of fluid in doing work is known as hydraulics‚ and the science of fluid in motion is known as fluid dynamics. INTRODUCTION The natural nature of fluids are they cannot remain stationary under the application of shear stress. However‚ fluid
Premium Fluid mechanics Force Fluid dynamics
This lab experiment investigates the effect of listening to different types of music on one’s pulse. The experiment relates the circulatory system to the pulse as it measures how quickly the heart contracts and releases blood. Pulse is measured in beats per minute (bpm). One’s pulse is loudest near the heart‚ because there is more pressure closer to the heart. In contrast‚ one’s pulse is quieter the further away it is measured from the heart‚ because there is less pressure the further the distance
Premium Heart Psychology Experiment