The purpose of this experiment was to acquaint the students with basic laboratory procedures‚ methods‚ and techniques; to introduce the use of basic laboratory measuring devices; to demonstrate different methods of manipulation of numerical quantities. DENSITY AND SPECIFIC GRAVITY Materials and Methods Part 1: Density of an Unknown Solid 1. We first were asked from our laboratory instructor to attain an unknown solid and were asked to note down the number of the solid. 2. Determine
Premium Density Volume
Name: Danielle Title: Unknown Lab Report Introduction: There are many reasons for identifying an unknown bacterium. The reasons range from medical purposes‚ such as determining if the unknown could cause ailments in living things or knowing what microorganisms are needed to make antibiotics. The experiment was done by applying methods in order to identify an unknown bacterium. An unknown bacterium was handed out by Dr. Honer. The appropriate tests were prepared and applied. The
Premium Bacteria Escherichia coli Microbiology
Ashley Spees CHM 261- Batzer Chem Final Write Up- Kool Aid Lab Total Acid This part of the lab requires titration of Kool Aid with an NaOH solution. The reason titrations are used is to determine the concentration of an unknown solution by reacting a strong acid with a strong base. Titrations are hard to accomplish‚ though‚ due to the fact that indicators used to show the endpoints are very sensitive and one drop could make the solution titrate past its endpoint. Blue stock solution: 3 mg/L
Premium Sodium hydroxide Base Titration
is the capacitative reactance‚ R is the resistance‚ and ω = 2π f ( f is the linear frequency). Apparatus • PC with DataStudio installed • Science Workshop 750 USB Interface Box • Power Amplifier • Voltage Sensor • AC/DC Electronics Lab Board • LCR meter • Connecting patch cords Experimental Procedure The experimental procedure can be divided into three parts: Part I: Using a Frequency Scan to Determine the Resonance Frequency • The first
Premium Alternating current Inductor Electrical resistance
Solutions by pH 6-2: Ranking Salt Solutions by pH In this assignment you will be asked to rank aqueous solutions of acids‚ bases‚ and salts in order of increasing pH. This is most easily done by first identifying the strong acids that have the lowest pH‚ the strong bases that have the highest pH‚ and the neutral solutions that have a pH near 7. The weak acids will have a pH between 1 and 6 and the weak bases between 8 and 14. The exact order of weak acids and weak bases is determined
Premium Acetic acid Chemistry PH
Experiment 3: ANALYSIS OF UNKNOWN ACID SAMPLE USING TITRATION METHOD Date of Experiment: 4 September 2012 Introduction An acid-base titration is a procedure used in quantitative chemical analysis to determine the concentration of either an acid or a base. Titration is the slow addition of an acid (or a base) of known concentration from a burette (a narrow graduated cylinder) to a base (or an acid) of unknown concentration fin an Erlenmeyer
Premium Titration Sodium hydroxide
all three solids precipitated at the bottom was heated‚ which allowed the PbCl2 to dissolve. The supernatant fluid containing the Pb(II) ions was then separated from the solid mercury(I) ions and solid silver ions decanting‚ adding a drop of acetic acid to the supernatant fluid‚ and also adding two drops of K2CrO4 to the test tube. A milky yellow mixture was observed as this indicated the presence of the lead (II) ion. This insoluble yellow precipitate was the insoluble compound of PbCrO4. In part
Free Solubility Solid Precipitation
References: a) http://en.wikipedia.org/wiki/Reynolds_number b) http://www.engineeringtoolbox.com/reynolds-number-d_237.html c) http://www.engineeringtoolbox.com/laminar-transitional-turbulent-flow-d_577.html d) http://www.slashdocs.com/prqt/lab-report-osbourne-reynolds-apparatus.html APPENDIX The Reynolds Apparatus that was used during the experiment.
Premium Fluid dynamics Fluid mechanics Viscosity
The Virtual Lab – ELISA Test Lab: Immunology 09/04/2013 Instructors: Dr. Charlie Wilson Written by: Dipen Patel I. Objective: The purpose of the lab was to learn the procedure of performing an ELISA test to determine whether a particular antibody is present in a patient’s blood sample. ELISA is an abbreviation for “Enzyme-linked Immunosorbent Assay." II. Introduction: The interaction of antigen and antibody outside the body can be used to determine if patient
Premium Antibody Immune system ELISA
Introduction In the amylase lab‚ it was being tested if amylase‚ an enzyme found in saliva‚ would be denatured by being put in an acid or high temperatures. This lab is about denaturing amylase. It is tested by exposing it to pH and temperature changes. It is then mixed with Benedict’s solution‚ is a solution that changes color from blue to reddish brown when maltose is present. Amylase breaks starch into maltose‚ so is the amylase isn’t denatured‚ it should change colors. Amylase is an enzyme
Premium Enzyme Starch Amylase