Designation: C 114 – 07 Standard Test Methods for Chemical Analysis of Hydraulic Cement1 This standard is issued under the fixed designation C 114; the number immediately following the designation indicates the year of original adoption or‚ in the case of revision‚ the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval. 1. Scope* 1.1 These test methods cover
Premium Oxide Cement Portland cement
Experiment No. ___________________ Date ___________________ NEUTRALIZATION TITRATIONS INTRODUCTION The neutralization of hydronium or hydroxide ion to form water is widely used as the basis for volumetric determinations of acids‚ bases and salts of weak acids. The reaction is characterized by a rapid change in pH near the equivalence point‚ a change that is readily detected by an acid-base indicator or that can be followed electrically by use of a pH meter. Neutralization titrations
Free PH PH indicator Titration
MARKS: 150 TIME: 3 hours This question paper consists of 16 pages and 4 data sheets. INSTRUCTIONS AND INFORMATION |1. |Write your centre number and examination number in the appropriate spaces on the ANSWER BOOK. | | | | | | | | | |Answer ALL the questions
Premium Chemical reaction Chemistry Sodium hydroxide
be cleaned thoroughly with tap water. While cleaning the buret‚ it is also checked to make sure there are no leaks. The ring stand is then set up with a buret clamp and the cleaned buret placed in it. Then the buret is filled with 5-10mL of sodium hydroxide‚ M .0466 NaOH‚ three times and emptied after each time to completely rinse the buret. The buret is now filled will NaOH until it reads at the 0.00mL mark on the buret. The initial volume of NaOH in the buret is then recorded into lab books
Premium Titration Sodium hydroxide PH
acid‚ is simply not enough. Next‚ a series of titration experiments had to be done. In the first series‚ a titration is completed of sodium hydroxide (NaOH) with KHP. Three reps were completed and the resulting data led to the finding of the molarity of the sodium hydroxide. The second part of the titration series involved titrating the same prepared sodium hydroxide solution with Hydrochloric Acid (HCL). This is how the molarity of the HCL was determined. The last part to the titration series
Premium PH Sodium hydroxide Acid
The Equilibrium Constant of an Ester Hydrolysis Reaction Julia Stanley CHM 152 LL Dr. Asmita Kane Budruk Goal of the lab: The purpose of this laboratory is to determine the equilibrium constant‚ Kc‚ for the acid-catalyzed reaction between an unknown ester and water to produce an unknown alcohol and an unknown carboxylic acid. I was using Unknown Ester #3 with a density of 0.9342 and Molar Mass of 74.08 g/mol; alcohol with density 0.7914 and Molar Mass 32.04 g/mol. Chemical
Premium Sodium hydroxide Chemical reaction Functional group
Data collection Quantitative Data Raw Data Table 1: Table showing the mass of the amount of unknown acid X measured in grams (±0.001g) Table 2: Table of reading of the burette initially filled with 25mL of 0.201moldm-3 sodium hydroxide (NaOH) to titrate 25mL (±0.03mL) of unknown acid X in mL (±0.05mL) after each titre. Reading on the burette initially filled with 25mL of 0.201moldm-3 NaOH (±0.05mL) First titre 21.3 Second titre 18.2 Third titre 15.2 Fourth titre 12.0 Qualitative
Premium Acid Sodium hydroxide Solubility
BIOLOGY LAB REPORT PRACTICAL M1 TESTING FOR MACROMOLECULES Title : Testing for Macromolecules Abstract : To test for macromolecules (carbohydrates‚ lipids‚ nucleic acids‚ and proteins)‚ iodine solution‚ alcohol‚ aceto-orcein stain and copper sulfate solution are used. The conclusions for all of the tests are positive. Introduction: A) Carbohydrate (starch) Carbohydrates are chemical compounds that contain oxygen‚ hydrogen‚ and carbon atoms. They consist of monosaccharide
Free DNA Protein Glucose
Procedure: 1. Each group will cut three agar cubes: A 3cm cube‚ a 2cm cube‚ and a 1cm cube. CUT AS ACCURATELY AS POSSIBLE. (This may be already completed for you.) 2. Pour 200mL of 0.1M sodium hydroxide solution into your 400mL beaker. 3. Immerse your 3 cubes in the sodium hydroxide solution‚ noting the time. 4. Let the cubes soak for approximately 10 minutes. 5. Periodically‚ gently stir the solution‚ or turn the cubes over. 6. After 10 minutes‚ use a spoon or tongs
Premium Sodium hydroxide Chemical kinetics
Taking 20ml of stock solution in a flask & then added 10ml of NH4OH.Then a white gelatinous ppt is formed which indicates the presence of Aluminum. Al3+ +NH4OH→Al(OH)3↓+ +NH4 Taken 20ml of stock solution ina flask & then add 10ml of sodium hydroxide solution slowly‚ a white gelatinous ppt is formed. Al3+ +NaOH → Al(OH)3↓+Na+ Then more NaOH is added to dissolve the ppt. Al(OH)3+NaOH→NaAlO2+H2O After sometimes added AlCl3 & Cobalt nitrate‚ then a blue ppt observed.
Free Sodium hydroxide Ammonia Solubility